CorSport specailizes in Honda (JDM) 1996-2000 Honda Civic Ferio (EK9) Window Visor Kit (4DR) - CorSport. Buy 1996-2000 Honda Civic Ferio (EK9) Window Visor Kit (4DR. Exterior parts for the 1996-2000 EK Honda Civic. JDM EK '96-'00 Civic Coupe/Hatchback Window Visors. Honda of Japan. » Installation Guides » Videos.

Necessary tools: - Flat Head Screwdriver - Phillips Head Screwdriver - Sharp Utility Blade - Black Pen - Tape If you bought these items new, this is how the box should show up to you: This is how the hardware should look: Make sure that you have everything in this illustration: For the purposes of this article, refer back to this picture for the particular clip location. (I will need to refer to specific locations throughout the article, so when I say �Location B�, look here). Take the first visor (I chose to start with the passenger side) and hold it up to the window where it should go. It should line up nicely with the edge of your side mirror.

Find great deals on eBay for EK Visor. For 96-00 Honda Civic 3Dr Hatch Smoke Tint Side Window Visors Rain Guard EK9. (How To install Speedzone Rear Roof Visor.

Now take some tape and secure it in place so that you can step back, check alignment, and realign if necessary. You do not NEED to tape it in place, but you are going to need to make some markings and it is much easier to do if you do not also have to hold the visor in place. You now need to mark the window trim in line with each hole in the visor. I started out using a Sharpie, but a black pen works better, especially later in the install.

Location A is very easy to do because you can clearly see the hole from the outside. Locations B-E are slightly more difficult. You just need to look at the visor from the top so that light is shining through the opposite side. Then mark the trim in line with the hole. This will show you where to install the clips when the visor is removed. Once you have marked all 5 locations, remove the visor and put it somewhere safe.

You now need to peel back your trim so you can install the clips. Carefully insert a flathead screwdriver into the trim, bring the screwdriver down to expose the gap, then lift the screwdriver all the way up, and then peel back the trim. Now, start with Location A. Have clip �3� ready. Get the small piece of cardboard that came with your visors and hold it up to the trim, level with the mark you made. Make a mark on the trim where the arrow on the cardboard points to. Now take clip 3 and position it so that the hole in the clip is aligned on the mark you just made.

Draw another dot on either side of the clip (perfectly above and below your current mark). Now join all 3 dots with a straight line. You now need to cut along this line. Make sure you go all the way through the rubber. Good Reader Crack Keygen Serial Key. You will feel the blade touch metal. Insert the end of clip �3� that has no hole. If you peel back the trim, you will see the end of the clip sticking out.

You now need to work most of the clip through the slit until it wraps around the rubber on the inside. There is a cross section of what this looks like in your instructions.

When it is in place and the trim is put back, this is what it should look like. Next grab clip 8. You will notice that the difference between clips �8� and 7 and 7 is the threaded hole in 8 is centered, whereas on 6 and 7, they are offset. Clip 8 goes in Location B. If you peel back the trim, you will notice that there is a hole in the metal there. The install of this clip is as simple as holding the clip under the metal while you secure it from the top with one of the silver screws (Number 9 from your collection of hardware). The next 2 locations are somewhat difficult to explain in words, but with the pictures, you should be fine.

These next 2 locations (C & D) each require 2 pieces are hardware (4 & 5). The cross section from the instructions shows how you insert clip 5. You then insert clip �4� to hold it in place. It won't feel very secure, but u will notice that with clip 4 in place, you can�t really get clip 5 out. The trim will then snug the whole thing up.

Now put your trim “back into place”. You need to now mark the trim on either side of your clip so you can cut out a small rectangle so that the trim fits snugly around the clip. You can now put your trim back together at that location to make sure it all lines up nicely.

Repeat these steps for Location D. For location E, there are a couple ways you can do it. Based on my research they both work. The first is to line the clip up on the metal like you did for Location B. The only difference here is that you need to drill the hole because there isn’t one there (unless you have a Type R, I believe). Autodata 2012 Download Deutsch Dictionary more.